BedSlats.co.uk - Importer and Manufacturer of bed components.

020 8863 7006

Mon - Fri: 8am - 5pm mail@bedslats.co.uk

Custom Slatted Bed Base First Generation (Double Row)

Availability:Made to order in approximately 7 days (3 day or same day service available)

Availability: In stock

£238.00

- First Generation Slatted Bed Base
- Made to Measure
- 100% Beech Sprung Slats
- Custom Sizes available 
- Fully Assembled in 2 pieces when delivered
- Usually manufactured & dispatched within 10 - 14 days
- Express Next Day & Three Day Service Available  


IT IS VERY IMPORTANT FOR ALL FRAMES THAT ARE SUPPLIED IN 2 PARTS THAT A CENTRE RAIL OR CENTRE RAIL FEET ARE USED, FAILURE TO DO SO COULD RESULT IN THE PRODUCT BEING DAMAGED.


£238.00

Custom Slatted Bed Base First Generation (921mm to 1840mm)

OUR CUSTOM 2 PART FIRST GENERATION SLATTED BED BASE CONSISTS OF:

-               40 Quality Beech Sprung Bed Slats (53mm x 8mm)
-               50mm by 20mm Beech Multiplex Ply frame
-               Single Slat Holders, which are dowelled into the side rails to add strength and durability
-               OPTIONAL: Adjustable slat tension adjusters in the lumbar region
-               Fully Assembled in 2 Parts when delivered  

TECHNICAL INFORMATION ABOUT OUR FIRST GENERATION SLATTED BASE 

HEIGHT OF THE SLATTED BASE

Approximately 63mm

GAP BETWEEN THE BEECH SPRUNG SLATS 

Approximately 43mm

MAXIMUM SIZES FOR OUR FIRST GENERATION SLATTED BASES

Minimum Width                   N/A        
Maximum Width                  Approximately 1840mm

Maximum Length                Approximately 2000mm

Extra Wide Double Frame First Generation Slatted bases can now be custom made, Please call us on 020 84222990 for more details and a custom quotation.

ADVANCE OPTIONS FOR OUR FIRST GENERATION SLATTED BED BASES

Optional: Adjustable slat tension in the lumbar region 

Eight First Generation adjustable tensions adjusters are placed in the lumber region to further improve your comfort level. These are also known as “rigidity adjusters”.

There are two beech sprung slats per single slat holder. These tension adjusters are placed in the lumber region, allowing the sleeper to manually adjust the firmness of their bed to their preference.

Another added benefit is that you can adjust the tension independently from your partner.

YOU’RE BED FRAME REQUIREMENTS 

Our Slatted Bed Bases are built to last for years. Your bed frame must have adequate support for the slatted bed base. 

The slatted bed base is there to support you and your partner and the bed frame needs to support the slatted bed base i.e. the ledges and centre rail (or Cross Rails) where the slatted bases rests on should be strong enough to hold your weight. 

Most beds have more then adequate support on the side ledges; however the centre of the bed may be an obstacle. We have many solutions if this centre support is not there. 

Heavy Duty CENTRE Rail Kit for Wooden Beds

You will be required to screw in our U shaped bed centre rail brackets on both your headboard and footboard area; this will need to be on the same level as your side ledges that are screwed on the inside of your bed side rails.  

You can also purchase one large or small adjustable foot for extra support if you feel it is required.   

Heavy Duty CROSS Rail Kit  for Wooden Beds 

This Product is an ideal solution if you do not have an area to screw onto on your headboard and footboard on the same level as your side ledges that are screwed on the inside of your bed side rails. 

These four cross rails will be placed width wise along the bed. Ideally you would place the first and last cross rail approximately 5 inches from the top and bottom of the bed. You would then spread the other two cross rails evenly between the first and last cross rails. 

You will need to remove your original side ledges that are screwed on the inside of your bed side rails. This is ideal as you can place the cross rails to your desired height; allowing you to choose whether you want your mattress to sit flush with the top of your side rails or if you want the mattress to sit within your bed frame. 

Heavy Duty CROSS Rail Kit for Metal Beds 

This Product is designed to sit on your metal bed Side Rails.

You will need to measure from the outside edge of the side rails to the other outside edge of the other side rail.  

The Cross Rails are 6cm in height. We will need an accurate measurement of the width of your Metal Side Rails. We will rebate 3cm by the thickness of your side rails, off the bottom end of the Cross Rail on both ends, consequently 3cm will sit on top of your side rails and the other 3cm will sit within your Metal bed Frame

We will also add a locking Mechanism on two of your Cross Rails to stop the Slatted Bed Base falling off the bed. Another benefit is that you will NOT be required to screw into your bed.

This Solution will add approximately 9cm to the height of your bed.

OTHER INFORMATION ABOUT THE FIRST GENERATION SLATTED BED BASE

Please note all First Generation Slatted Bed Bases are manufactured to order, you will be required to inform us of the internal dimensions of your wooden bed frame; as this will be the maximum area available for your slatted base.

Other Measurement will be required for Metal beds.

Please note that the colour of the components may vary, for exact colours please call us

The lead time for our made to measure slatted bed bases is approximately 14 days from the date of order; however we may also be able to offer an express service.

IT IS VERY IMPORTANT FOR ALL FRAMES THAT ARE SUPPLIED IN 2 PARTS THAT BOTH THE FRAMES ARE SUPPORTED ADEQUETLY; FAILURE TO DO SO COULD RESULT IN THE PRODUCT BEING DAMAGED.

Delivery Price

Customer Reviews

Quality of Product

test test1

test

Great advice from Reg regarding the perfect product to suit my needs and excellent guidance on measurements to ensure a perfectly fitting product. Would recommend to anybody.
Peter

Very prompt manufacture and delivery. Very well made, easy to instal and fitted into my bed frame perfectly - replacing my too firm solid pine slats.
Reg and Simon very helpful, with Reg coping with all my detailed queries and concerns re measurements - and reducing the depth of the slatted bed base to sit into my bed frame.
Good quality and value for money.

I moved from the US to London and had a US sized bed frame that needed a new bed base, found it extremely difficult to find a company in the UK who supplied slats for my US sized bed.

This company was fantastic to deal with, Reg was a great help with his technical knowledge, my bed base was made to order and fitted by odd sized US bed frame perfectly.

A true example of genuine British manufacturing. Thank you so much.

Katrina


Write Your Own Review

How do you rate this product?

  1 star 2 stars 3 stars 4 stars 5 stars
Quality of Product

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.